At 5.40 on a Friday morning, the night supervisor at a residential aged care home walks the last wing before handover. Hot water in the ensuite on room twelve is lukewarm again, the thermostatic mixing valve has been temperamental all week, wing B air conditioning has been blowing warm since midnight, a fault has been reported at the fire-alarm call point in the corridor, and the resident bathroom near the nurses’ station is blocked. The lift between the ground floor and the first-floor wing stuck twice overnight. Someone texts a plumber, someone else writes “air con — wing B” on the whiteboard in the staff room, and the facilities officer will pick up three voicemails after morning medication rounds have already started.
For an aged care home, the morning is judged by whether plant and wings are ready before care starts. A cold shower before a wash, a warm wing before breakfast, a blocked bathroom beside the nurses’ station, or a lift that will not carry a resident to the dining room — each one lands on the floor team before the regional facilities manager even opens email. Across a portfolio, the same night can bring a hot-water fault at one home, a fire-equipment defect at another and a stuck auto door at a third, each handled by whoever is on night shift.
OpsChase puts aged care maintenance across your homes on one board: each plant-room and resident-wing fault is raised with a photo against the home and the area, it goes to your own team or your contractors and is tracked until the work is done, and the regional facilities manager can see which homes still have open faults before morning rounds.
From an overnight fault to a work order
The night supervisor or the facilities officer raises a work order from their phone against the home and the area: ensuite hot water lukewarm on room twelve, wing B air conditioning blowing warm, fault reported at the fire-alarm call point in the east corridor, resident bathroom blocked near the nurses’ station, lift stuck between floors. They add a photo and a note, and mark whether the area affects residents or can wait until after breakfast.
Someone on your own team can take the small jobs straight away, such as replacing a soap dispenser or restocking bathroom supplies, and close them on the same work order. Electrical work and anything else that needs a licensed trade goes to appropriately qualified staff or contractors — a thermostatic mixing valve (TMV), heating and cooling, fire protection, a lift or an auto door — with the details already on the job, so nobody rings the home back to ask which wing it is.
OpsChase looks after the buildings, the plant and the people who work on them. Clinical records, care plans, medication charts and Aged Care Quality Standards documentation stay in the systems you already use.
Your contractors per home and per trade
The plumber who knows the thermostatic mixing valves at your city home may not reach the regional home before morning rounds. Name your regular contractors per home and per trade, including the firm that services your lifts and fire equipment.
The faults morning rounds notice first
- Hot water and bathrooms. Lukewarm ensuites, failed thermostatic mixing valves and blocked pans go to plumbing; sanitary bins and dispensers go to washroom hygiene; a bathroom that needs a deep clean goes to cleaning.
- Wing comfort. Air conditioning and plant-room heating and cooling go to heating and cooling; dead power points and failed night lighting go to electrical; portable equipment due for testing goes to test and tag.
- Fire and call equipment. Fire-alarm call point defects, extinguisher faults and essential fire equipment go to fire protection.
- Access and movement. Auto doors and wing doors that will not open or close go to doors and shutters; a lock that will not turn goes to locksmith; cameras and alarms go to security; a lift that will not travel goes to lifts.
- Grounds and pests. Paths, gardens and outdoor seating go to grounds and landscaping; pest sightings in kitchens or stores go to pest control.
Attend-by times set around morning rounds
Set attend-by times using your home’s risk assessment and emergency procedures. Keep urgent hazards visible separately from routine repairs; use your home’s emergency process when residents may be at risk.
Add a note on when the contractor can work on site: after breakfast in a vacant ensuite, with a wing escort, or outside quiet hours with the night supervisor’s sign-in. Late jobs show against your response targets, so the regional facilities manager can see which homes are still waiting before morning rounds, not after the weekend.
Compliance and site access before anyone is booked
Keep licence, public liability, induction and site-access details on file for each contractor firm through contractor compliance, so the team can check them before booking. Add home notes on where contractors sign in at reception, which entrance to use clear of ambulance bays, which wings need an escort, and where the plant room, switchboard and fire panel are.
Proof before the area reopens to residents
Set proof templates per job type: before and after photos, a note from the contractor, and a certificate where electrical, plumbing, fire or lift work needs one. With proof of completion on the work order, the night supervisor and the regional facilities manager can review the contractor’s completion record. Your home’s checks and procedures determine when the bathroom or wing can reopen to residents.
Faults that keep coming back
Some faults return every few weeks: the same thermostatic mixing valve, the same wing air conditioner, the same auto door. With Assets & planned maintenance switched on, each thermostatic mixing valve, air conditioning unit, lift, fire panel and auto door keeps its own job and service history, and you can run planned maintenance such as TMV servicing, filter cleans, lift inspections and fire-equipment checks through scheduling on the same board as reactive jobs. When the wing B unit fails again, every visit is on the record, so the call between another repair and a replacement is made on what happened, not on memory.
What the regional facilities manager sees on one board
With every home on one board:
- Faults come in with a photo, the home and the area.
- Your own team takes the small jobs; your regular contractors take the rest for each home and trade.
- Attend-by times put bathrooms, fire doors, lifts and wing comfort before cosmetic work.
- Photos, notes and certificates are attached to the work order.
- The regional facilities manager sees every open job across the portfolio in one view.
For the wider picture across homes, read about multi-site maintenance. The aged care industry page and the aged care audit-pack show how close-out packs look across a sample of homes.
Starting with one home
Pick the home with the most overnight faults. Import its plant rooms, wings, bathrooms, lifts, fire equipment and auto doors, the contractor book and the trades each firm covers. Set roles for the night supervisor, the facilities officer and the regional facilities manager. Set proof templates for plumbing, heating and cooling, fire and lift repairs. Raise the next hot-water or wing fault into OpsChase instead of a text, then add the next home.
Read the aged care industry page or book a demo with your home list and contractor book. Check pricing when you are ready to bring every home onto one board.
Residents and families will still find the odd lukewarm shower. The difference is that every fault is recorded, assigned and tracked until the work is done.
