From 1 December 2026, Safe Work Australia’s workplace exposure limits replace the workplace exposure standards for airborne contaminants. Safe Work Australia says the transition period ends on 30 November. Most states and territories adopt the new list from 1 December, but some have different commencement dates or interim limits for particular substances, including diesel particulate matter. Check your work health and safety regulator for the limits that apply at each of your sites.
If your sites run diesel forklifts, standby generators, loading docks with idling trucks, vehicle workshops, or any cutting, grinding or cleaning that puts dust, fumes or vapours in the air, this change is worth a few hours of checking at each site before the date.
This post isn’t legal or occupational hygiene advice. Read Safe Work Australia’s guidance on workplace exposure limits, talk to your work health and safety regulator about how it applies in your state, and bring in an occupational hygienist where you need air monitoring.
What changes on 1 December
- The list changes name and values. The workplace exposure standards become the workplace exposure limits, and a number of values have changed after the first full review since 2003. The new name makes the point that these are limits not to be exceeded.
- Diesel exhaust has a new national limit, but not every state applies it on 1 December. Safe Work Australia’s list sets diesel particulate matter at 0.01 milligrams per cubic metre, measured as respirable elemental carbon over an eight-hour shift. That figure applies from 1 December 2026 where a jurisdiction has adopted it. In Victoria and Queensland the diesel limit from 1 December 2026 is 0.1 milligrams per cubic metre, with the 0.01 figure due on 1 December 2029 (underground mining in Victoria stays at 0.1). Western Australia has not changed its diesel particulate limit; WorkSafe Western Australia is doing a regulatory impact assessment first. Any site with diesel plant running indoors or near doorways should check the limit that applies in that state, then measure against it.
- The duty is the same. The business running the site must eliminate airborne contaminants where it reasonably can, and otherwise minimise them so nobody is exposed above the limit. If you’re not sure whether a site is under the limit, air monitoring is how you find out.
Site checks to run before 1 December
Run the same short list at every site, and write down what you find for each one:
1. List what’s in the air. Diesel plant, generator exhaust, welding and cutting fumes, silica and timber dust, solvents, paint, and cleaning chemicals. Note which sites use or make each one. 2. Check each one against the new list. If you already know what’s in the air at a site, check whether its limit has changed. 3. Book air monitoring where you’re unsure. An occupational hygienist can measure what workers are breathing and tell you whether a site is under the limit. 4. Fix the controls, most effective first. Swap or remove the source where you can: an electric forklift instead of a diesel one, or a wet cut instead of a dry one. Then engineering controls: ventilation and extraction fans serviced by your heating and cooling contractor, generator exhaust pointed away from doors and air intakes by your generator contractor, and machinery from plant hire firms serviced so it runs clean. Then work rules, such as engines off while trucks wait at the dock. Respiratory protective equipment comes last, and only works when it fits and is worn properly. 5. Check it worked. Review the controls once they’re in place, and test again where the first result was close to the limit.
Older buildings add one more check. If you’re cutting or drilling into walls, ceilings or floors that may contain asbestos, stop and get an asbestos assessment before the work goes ahead.
One job per control, per site
Most sites will finish these checks with a short list of work: an extraction fan that needs servicing, a generator exhaust that needs moving, a dock that needs signs and a timer on the roller door, a cleaning product to swap for a milder one with your cleaning contractor. Treat each one as a job, not an email:
- Raise each fix at the site it belongs to, with photos and the monitoring result attached.
- Book the work in priority order, so the site with the highest reading gets fixed first.
- Keep the hygienist’s report, service records and photos with each job, so you can show what was found and what was done at each site.
If your sites ran generators through the recent storms, our power outage checklist and storm season checklist cover the restart and make-safe work.
Running exposure fixes on one OpsChase board
OpsChase is one AI-powered platform for running maintenance across one site or many. The checks above turn into jobs that land in one place:
- Anyone can raise a job from their phone, with photos, whether it’s a site manager, a work health and safety lead or the person who read the monitoring report.
- Jobs are booked to your own team or your contractors. Set your regular contractors per site and per trade, such as the ventilation service firm, the generator contractor and the hygienist for each site, so each job goes to the right regular contractor.
- Jobs are sorted by priority across every site, so the workshop with the highest diesel reading isn’t waiting behind a car park sign.
- Each job is tracked until the work is done, then closed with proof of completion: photos and sign-off on the work order.
- Keep licence, public liability, induction and site-access details on file for each contractor firm through contractor compliance, so the team can check them before booking anyone onto site.
With Assets and planned maintenance switched on, extraction fan servicing, generator servicing and repeat air monitoring become planned maintenance, booked at every site on the dates you set. Those jobs sit beside your scheduling so you can see who is on shift before you book the work. Each fan, generator and forklift keeps its own service history, so you can see what was done and when.
What the manager sees
Across every site, the manager sees one board:
- Every exposure control job, by site, sorted by priority.
- Who is booked to attend each job, with the monitoring report and contractor notes.
- Which sites have finished their checks and which still have open jobs.
- Late jobs showing against your response targets.
For more on running several sites from one view, see multi-site maintenance and facilities maintenance.
Where to start this week
There are only a couple of weeks left before 1 December. List the diesel plant, generators, docks, workshops and dusty work at each site. Check each contaminant against the new list, and book an occupational hygienist for any site where you’re unsure. Then see how OpsChase runs the fixes on pricing, or book a demo with a list of your sites.
When the new limits start, every site has been checked, and every fix is on one board.
